Kohei Fujii Guitars

Kohei Fujii Guitars

Sunday, October 28, 2012

Nylon Model Complete

This week, I completed the Nylon model. This guitar has about 2" smaller body size compared with the predecessor shown in the 3rd photo. Purpose of shrinking the body size is to obtain more quick response, and less strong bus for Jazz musicians. This guitar showed very similar sound character as the full size version. Difference is simply just a little bit quiet. Other than that, new mini version has very similar results. I was a little bit surprised from this results. From this experience, I have gotten a conclusion that as long as a guitar has same bracing patter, guitar creates similar sound character.
Another difference for this nylon model is material. This guitar has Oregon Myrtle side and back. Myrtle created shorter sustain. This sound character is suitable for Jazz music. I designed this model as a platform for installing a pick-up system. I will install electrical pick-up system soon. I will report once I got an electrical version of this guitar.





Sunday, October 21, 2012

MD Complete

A long jury to complete MD model is finally over. I completed MD making this weekend. This guitar gave me a very satisfying sound quality. This guitar has amazingly long sustain and tonal response. A 12-deghree head angle design gave me a very player friendly string tension without sacrificing tonal quality. This is an amazing surprise. I hope this guitar satisfies a new owner's desire for owing a new guitar, and to be a good partner of a new owner. This guitar will be shipped to Japan tomorrow.






Sunday, October 14, 2012

Final polishing and Bridge install

     Finally. MD model completed final sanding and polishing. Sanding session started with 600-grit sanding paper through, 1200-grit, and 2000-grit. Top photo is for after 600-grit sanding session, and second one is after 1200-grit session. After finishing the 2000-grit sanding, I had polishing sessions. Then, I did bridge install. Bridge install has been done by a vacuum clamp with 20Hg vacuum setting. My bridge has super thin wings thickness; therefor, I need the vacuum clamping system. It is almost impossible to install my unique bridge using a conventional clumping technique.
     I checked neck angle to the installed bridge. It looks perfect. I will have a final fret dressing session, nut and saddle making. Then, this guitar is ready for a test drive. I might be able to complete MD guitar making project next Sunday.










Sunday, October 7, 2012

Bridge Making

While waiting the final coat curing, I made bridges for MD and nylon model. MD employed Madagascar RW, and Nylon model employed Brazilian RW. Nylon bridge is made from three-piece configuration due to the material size limitation. Both of bridges have 28-grams of wait. My bridges are always less than 28-grams. I do not like heavier bridge, for my tonal preference. So, I almost have never used Ebony bridges. My bridges are finished by couple of coats of Shellac including a pumice pore filling process. Last three photos show design matching between bridge and the body. For me, both MD and nylon model have excellent design matching including color. Next week, I will have final sanding and polishing sessions.








Sunday, September 30, 2012

Final coat apply

     I finished final coat spraying. We have a heat wave this weekend, and the highest temperature is around 90 degree-F. I started spraying session early morning to avoid high temperature issue. I was able to spray quite nicely. I have been using a water based acrylic lacquer from Target coatings. I had very good results from previous Target products. This time, they discontinued the previous version, and upgraded a new version. This time, I used Emtech 7000. I sprayed with my HVLP spray with a 1.4mm spray tip, and 40-psi air pressure. This setting makes best spraying control for me. I also made an armrest for the nylon model. The armrest is made from a Maple. I black died the armrest.
     I will take approximately 7-9 days to get complete cure for final sanding and polishing sessions. White waiting the curing, I make bridges and bone nut and saddle.








Sunday, September 23, 2012

Filler leveling

There is not much progress visually; however, I did a lot of work this week. I did leveling sessions for Epoxy filler to get the final spray session ready surface. I needed two filler applying sessions for Spanish ceder necks. King-wood body and Myrtle body were able to obtain nice leveling with only one session. After finishing the leveling session, I applied an Alcohol thinned Epoxy coat to optimize color difference due to an excess sanding during the surfacing session. It takes approximately 48-nours to obtain complete Epoxy cure for the Epoxy coat, because the Alcohol work as a retarder.  Now, both MD and Nylon model are ready for final coats spraying. I will spray 10-filanl coats in two days next weekend.

There is a question from the MD client. His question is that this body seems a bit thicker than ordinal D-size guitar. This MD body does not have thickness modification. Thickness at the bottom is 120mm ,and at the neck joint, it is 94mm.