Kohei Fujii Guitars

Kohei Fujii Guitars

Sunday, October 4, 2020

Rosetta making

 I did Rosetta making this weekend. MD has a Brazilian RW Rosetta with original ornamental. I have not done the install work for the ornamental. However, I will do in next couple of days. I also completed the sound hole cut. Inside of the sound hole, I also added a black dyed poplar. This additional layer is able to seal a moisture penetration to the spruce top cross grain. This additional work not only makes a unique look for the Rosetta, but also makes an additional moisture resistance. 






Sunday, September 27, 2020

New bracing pattern and Top brace wood making

     This is a 12th fret joint MD model, and I need to modify the existing bracing pattern for 12th fret joint. I needed to move the sound hole position 10mm toward bridge. This modification requires for the 19th fret fingerboard design. Photo is the new bracing pattern for the MD 12th fret joint. Bridge plate location also needs to move a little bit tail side. 12th fret joint design is able to install the bridge at an ideal location on the sound board, from a view point of the sound board vibration. I am very excited about making a 12th fret joint MD model. This design will make very nice over tones. 

     I cut brace wood from chopped Adirondack spruce logs. This material looks like fire wood. However, this material has been stored couple of years in my shop. I have been using Adirondack spruce for bracing with very good results. Adirondack is also very easy for shaping using chisel, knife, and small plane.








Sunday, September 13, 2020

Custom MD project Start

 I started a custom MD project. This is a 12th fret joint MD model. The goal is to make a guitar with  many overtones possible. Top is a Carpathian spruce. Rosetta is a Malaysian black wood with three original ornaments. I made original ornament couple of years ago. This cute ornament makes a unique Rosetta.













Sunday, August 30, 2020

00 Mahogany complete

 00 size Mahogany body 14th joint model complete. Specifications for this guitar are shown below.

Size: Martin 00 size

String scale: 650mm

Strings: D'addario EJ-16

Top: Adirondack spruce with Adirondack X-bracing

Sides: Figured Mahogany with Yellow Ceder laminate

Back: Figured Mahogany with Adirondack spruce lattice bracing

Body has two carbon fiber rod reinforcements from the neck block to the body-back for preventing the body deformation issue. 

Body Bindings and Center strip: Ebony with BW trim

Rosetta: African Padauk with original ornaments

Neck: Three-piece Spanish ceder with Vee-jointed head.

Neck Joint: Permanent joint with two mortises (Ervin Somogyi style)

Neck reinforcements: One way truss rods and two Graphite rods.

Tuning machines: Schaller Grand Tune

Front Head Veneer: African Black wood 

Back Head Veneer: Catarox

Finger board: African Black wood 14th fret joint and 650mm scale

Neck Heal: Ebony

Bridge: African Padauk

Bridge Pins: Ebony

Nut and Saddle: Bleached Cow Bone

Case: Gator











Wednesday, August 5, 2020

Ukulele Complete

Ukulele Making is complete. I made this ukulele as a gift for my closed friends they recently moved to Maui Hawaii. This ukulele has the balsa and graphite epoxy composite top with A-frame bracing. This design created a very successful result. This ukulele showed super crispy sound. I also used super thin top thickness. I also installed a graphite rod in the neck. For the finishing, I used water based acrylic lacquer spraying. So, the ukulele has enough robustness for daily use. I hope, this ukulele becomes a nice music companion for the happy couple in Maui.   







Sunday, June 28, 2020

Ukulele making

     I have been working on a Ukulele making. This is a concert size Ukulele using a lattice bracing.
Mahogany top, back, and side. This Ukulele has a high technology balsa lattice bracing with Carbon fiber Epoxy lamination for the top. This technique has been using my classical guitar model with super nice tone. Back also has my signature design using the lattice bracing. So, this Ukulele is my original lattice bracing design. Top has only 1mm thickness to obtain super nice response. To make a strong enough top from only 1mm thickness, I designed an A-frame configuration near the sound hole. You may see the brace looks like the A character. This A-frame configuration enables to distribute the neck tension evenly to the entire top.
     Body construction is already completed. I installed premium quality Hawaiian Koa binding for top and back. I will work the neck making next week.






Thursday, November 28, 2019

Classical Project Complete

     I completed the classical guitar making project. I installed strings in 11/23/2019 first time. Strings action over the 12-fret wire is 3.4mm for the low-E and 3mm for the high-E. This is quite low action setting. I installed the D'Addario EJ45 normal tension strings. This guitar has been improving the sound quality day-by-day. Now, I have good confidence that this guitar has very nice bright sound character. Low-E string has very power full sound. I feel strong vibration in my stomach, when I hit the low-E string. This result is due to the graphite rod reinforcement in the last photo. Those carbon rods braces hold the neck very tight. Also, those braces are able to avoid future deformation issue for the neck angle change. Carbon braces are super light weight; therefore, the additional weight penalty is very minimum. I am very happy with this results.
     Please enjoy posted photos for the completed Classical guitar. The guitar specifications are shown in below.

Strings Scale: 650 mm with African Black wood fingerboard
Neck profile: 52 mm at nut and 62 mm at 12 Fret
Neck: Cedro-Black Dyed Maple-Maple-Ebony-Maple-Black-dyed Maple-Cedro (7-play) with a Graphite rod reinforcement
Top: European Spruce with Balsa and Graphite with Epoxy composite
Back: Curly Maple from West coast USA
Sides: Curly maple and Yellow Cedar laminate
Bridge: Brazilian Rosewood
Binding: Ebony
Tuning machines: Gilbert
Head plate veneer: Ebony (top and back)
Armrest: Black dyed maple
Nut and saddle: Bone
Finishing: Shellac (top) and Water based acrylic